汽車上的大多數傳感器信號都會(huì )通過CAN/LIN總線傳輸到ECU控制器，ECU對數據進行處理后，又會(huì )通過CAN/LIN總線對執行機構發出控制信號，使各部件按照要求正常工作。如果某個部件工作異常，就需要判斷是否是總線傳輸過程出了問題。

Most of the sensor signals on the vehicle are transmitted to the ECU controller via the Can/lin bus, and after the ECU has processed the data, a control signal is sent to the actuator via the Can/lin bus to make the parts work as required. If a part is working abnormally, it is necessary to determine whether the bus transmission process is out of the question.

汽車檢測設備切削加工中的測量主要是對缸體上的缸孔、主軸承孔和中間軸孔，缸蓋上的氣門閥座孔、氣門導管孔、氣門調節器孔和凸輪軸孔，連桿上的大、小頭孔，曲軸的導向軸徑和第三主軸徑寬度等加工完成后尺寸的測量以及對缸孔的分級測量，且均配有工控機。其中缸體上的缸孔、曲軸的導向軸徑和第三主軸頸寬度等除了測量外還配有刀具自動補調系統。

In the machining of automobile inspection equipment, the measurement of the cylinder bore, main bearing hole and middle shaft hole, the valve seat hole, the valve orifice, the valve adjuster hole and the camshaft hole, the large and small head hole on the connecting rod, the shaft diameter and the third spindle diameter width of the crankshaft are measured and the cylinder bore is graded. and are equipped with industrial computer. The cylinder bore on the cylinder, the shaft diameter of the crankshaft and the width of the third spindle neck are equipped with automatic tool adjustment system besides measuring.

汽車檢測儀介紹，好的汽車解碼器或汽車干擾器就像汽車的“黑匣子”，能夠隨車記住汽車各方面的數據，然后基于機器視覺通過電腦系統分析對比就能找出故障所在，當然，這也是汽車解碼器和干擾器被研究出來的真正意義，現在幾乎所有的汽車維修４Ｓ店與高檔汽車維修店都已配備了汽車解碼器與干擾器這種檢修工具。

Car fault detector, a good car decoder or car jammers like the car's "black box", can follow the car to remember all aspects of data, and then based on machine vision through the computer system analysis and comparison can find fault, of course, this is the car decoder and jammer is the real meaning of the study, Now almost all of the car repair 4S stores and high-end car repair shops have been equipped with a car decoder and jammer for this overhaul tool.

汽車檢測設備大多是計量檢測儀器，一旦這些設備不準，故障可能找不出來，或導致錯判故障原因，汽車的調試和安裝就難免發生偏差。不過，市市場監管局南山分局相關負責人介紹，雖然多數設備沒有納入強檢范圍，但每一種設備都有其標準，并規定了偏差允許的范圍，一旦超過了規定范圍，就是不合格設備。

Most of the vehicle testing equipment is a measuring instrument, once these equipment is not allowed, the fault may not be found, or lead to the wrong reason, the commissioning and installation of the car will inevitably occur deviations. However, the City Market Supervision Bureau Nanshan branch of the relevant person, although most of the equipment is not included in the scope of the strong inspection, but each of the equipment has its standards, and set the scope of the deviation allowed, once the specified range, is unqualified equipment.

常用底盤及整車檢測與診斷設備：底盤測功試驗臺，汽車制動試驗臺， 常用底盤及整車檢測與診斷設備，底盤測功試驗臺，汽車制動試驗臺，汽車側滑試 常用底盤及整車檢測與診斷設備 驗臺，電腦四輪定位儀等。 驗臺，電腦四輪定位儀等。

Common chassis and vehicle testing and diagnosis equipment: Chassis dynamometer test bench, automotive brake test rig, commonly used chassis and vehicle testing and diagnostic equipment, chassis dynamometer test bench, car brake test rig, car side-slip test commonly used chassis and vehicle testing and diagnostic equipment, computer four-wheel positioning instrument. Test bench, computer four-wheel positioning instrument and so on.

深圳市創(chuàng )盈時代科技有限公司是一家專注于機器視覺，視覺檢測設備，CCD光學檢測設備，機器視覺檢測，視覺方案定制，非標自動化設備的研發生產和銷售于一體的國家高新技術企業。